Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
Last revision Both sides next revision
block:server_rack [2018/07/04 00:37]
lperkins2 [Server Rack] Update
block:server_rack [2020/05/23 09:01]
payonel
Line 13: Line 13:
 In the middle are 5 vertical lines, corresponding to each side of the rack except the front. ​ A key for which line is which is present on the right. ​ When a server is inserted into a slot on the left, a '​primary'​ node is added to each vertical line.  Clicking on one of these nodes connects the Server to the side of the case controlled by that line.  If the server has a [[item:​network_card|Network Card]] in it, a smaller node is created under the primary node for each network card in the server. ​ Like the primary node, clicking on one of the smaller nodes connects the network card to a side of the case. In the middle are 5 vertical lines, corresponding to each side of the rack except the front. ​ A key for which line is which is present on the right. ​ When a server is inserted into a slot on the left, a '​primary'​ node is added to each vertical line.  Clicking on one of these nodes connects the Server to the side of the case controlled by that line.  If the server has a [[item:​network_card|Network Card]] in it, a smaller node is created under the primary node for each network card in the server. ​ Like the primary node, clicking on one of the smaller nodes connects the network card to a side of the case.
  
-The single button on the Server Rack GUI does not appear ​to change anything beyond drawing ​a line between ​the boxes at the bottom of the vertical lines.+The single button on the Server Rack GUI connects and disconnects each of the faces of the rack to each other. When enabled (horizontal ​line is drawn across ​the boxes at the bottom of the vertical lines), modem messages and power will pass through the rack - essentially,​ the rack acts like a cable. When disabled, different networks on different sides of the rack will remain isolated and no messages or power will pass through the rack.
  
 Servers inside the case can be accessed by right clicking on them in the front of the Server Rack.  This will open their component view, similar to right clicking a normal computer case.  To open the Rack GUI again, right click on the side of the Server Rack, or above or below any installed Servers. Servers inside the case can be accessed by right clicking on them in the front of the Server Rack.  This will open their component view, similar to right clicking a normal computer case.  To open the Rack GUI again, right click on the side of the Server Rack, or above or below any installed Servers.
  
 Wired network messages can only be sent between Servers with Network Cards. ​ The Network Cards must be configured in the Server Rack GUI to share a side.  To send or receive messages on an external network, the Network Card must be connected to the side of the case with the external Computer or [[block:​switch|Relay]]. ​ If you want Server-Server internal networking, without cross-talk outside the case, set the Network Cards to the case's unused side (as there are 5 valid sides, and a maximum of 4 servers, there is always an unused side). Wired network messages can only be sent between Servers with Network Cards. ​ The Network Cards must be configured in the Server Rack GUI to share a side.  To send or receive messages on an external network, the Network Card must be connected to the side of the case with the external Computer or [[block:​switch|Relay]]. ​ If you want Server-Server internal networking, without cross-talk outside the case, set the Network Cards to the case's unused side (as there are 5 valid sides, and a maximum of 4 servers, there is always an unused side).
 +
 +The Server Rack also has a Relay Mode which can be used using the Enable/​Disable button in the gui. When the rack is in relay mode it acts like a [[block:​switch|Relay]] and repeats wired network packets to external components that are connected to the rack block.
  
 The Server rack is crafted using the following recipe: ​ The Server rack is crafted using the following recipe: ​